US$130
for 0 classes무엇이 포함되어 있나요?
숙제
주당 1-2시간. Students will be required to watch the recordings of the class and complete the assigned weekly tasks. Students will upload pictures and videos of their projects as well as copies of their code to the Classroom page in Outschool. In addition, there will be weekly posts that students will need to respond to in order to demonstrate participation in the class.학습 평가
Students will not receive grades unless requested by the parent. Assessment of assignments will be informal, consisting of posted feedback on projects, videos, and code.채점
포함됨보고계신 지문은 자동 번역 되었습니다
수업 소개
INTRODUCTION: In this 10-week FLEX class (no live classes), students will learn how to use a wide variety of digital and analog actuators to code an Arduino Uno to create inventions and projects. This class will build on the foundation that students gained from my Arduino Parts 1 and 2 FLEX classes to allow students to incorporate more advanced devices into their projects. Each week, students learn about a different component culminating in a final project that students will create and share with the class. Students will learn how to hook up and code the following actuators: active and passive buzzer, relay, servo, LCDs, 1-digit LED, 4-digit LED, LED array, DC motor, and stepper motor. Students will learn how to download and properly install Arduino Libraries that are needed for some of the actuators. FORMAT OF THE LESSONS: Every Sunday, a new lesson will be posted in the classroom on Outschool. Each lesson begins with a recorded video that is uploaded to the classroom in Outschool. A combination of the Arduino IDE and TinkerCad are used to teach the lessons in the videos. Provided in the video are detailed explanations of how to connect the devices to the Arduino and how to write code to read the sensors. A link to Arduino libraries will be uploaded to the Classroom page so that students will be able to locate and download the libraries for their use. Each video begins with a short PowerPoint presentation that explains the basic principles. This is followed by a detailed guided demonstration that shows how to connect the components and the code used to control them. Each student is expected to actively participate by following the directions described in the lesson using their components and the Arduino software and or using the simulation on TinkerCad. It may be helpful to have separate devices: one for watching the video and a computer to try out the lessons. This will make it easier to follow along with the lessons. IMPORTANT: If you are using an actual Arduino, you will need to have access to a computer and not just a chromebook or tablet because the Arduino IDE does NOT work on those devices. Each week, an activity worksheet will be posted in the classroom that describes the objectives of the lesson, any libraries needed for the device, and a list of activities to try. Students will have one week to complete the activities and are required to share their results and participate in the classroom discussions as described below. STUDENT INTERACTIONS: Students are expected to interact with each other and with the teacher every week within the framework of the Outschool Classroom site. Students will be required to use discussion forum to post responses to worksheet questions, upload code for worksheet assignments, and share videos of weekly project assignments. During the first week of the class, students will be required to post a video or a paragraph introducing themselves and stating what they hope to learn. Every week thereafter, there will be post describing the interactions required for that week's lesson. These instructions will be provided on a worksheet as well as posted in the discussion forum. Interactions will include prompts for discussion, games, contests, surveys, sharing work, and posting videos of projects. Students will receive weekly feedback from me about their responses, code, videos and comments. I will provide help and encouragement as students become proficient in their coding skills. Students who feel they need additional assistance can request a live meeting with me and I will be happy to try to arrange it. Some interactions will begin as a prompt posted in the classroom. These prompts will be used to initiate discussion, reinforce concepts and assess knowledge. For example, I may post a prompt, such as “Name one digital actuator and one analog actuator.” Other prompts will include brainstorming activities, games or surveys. For example, I may ask students to list a device they encountered during the week that contains an actuator and identify it, An interactive game that will be used is "I'm thinking of a device" whereby each student must submit the name of a device that meets the criteria. For example, "I'm thinking of a device that uses an LCD." The first student that responds correctly gets to write the next “I’m thinking of a device” question. During the last week of the class, students will share their final projects with the class. Students will post their final project code and a video explaining their project, how it works, and the challenges they encountered. Students will be required to provide feedback to two of the other students about their final projects. If it can be arranged, a live class will be scheduled so that students can share their projects in real time. PRIOR KNOWLEDGE: Students should either have completed Arduino Coding Part I and Part 2 or have basic knowledge of the skills taught in those classes. They should know how to wire and code the following devices: LED, RGB LED, serial monitor, ultrasonic sensor, servo, photoresistor, thermistor, button, potentiometer. They should have basic knowledge of the Arduino coding syntax and be able to use simple “if/else,” “while,” and “for” loops. Students need to have an Arduino Uno or Arduino Mega for this class, as well as the actuators that will be taught. Please see the recommended materials and kits listed in the " Supply List" shown below. Please see the list of weekly topics in the Learning Goals section below.
학습 목표
Class 1: What are actuators?
- Definition
- Examples of actuators (motors, servos, LEDs, Displays)
- Digital actuators (LED, active buzzer, relay, vibration motor)
- Actuators that use digital pins but need libraries (servo)
- Actuators with shields or motor drivers
- Uploading Libraries
Class 2: Active vs passive buzzer
- Using tone command
- Pitch library
- Using arrays
Class 3: Servos
- 180 vs Continous servos
- How to control 180 servo, sweep, knob
Class 4: Stepper Motor and Motor Driver
- How to count steps (make a clock)
- Control stepper motor with a rotary encoder
Class 5: : LCD screen
- Library
- How to connect the LCD
- How to write to the LCD
- Read sensors and write value on the LCD
Class 6: LED array
Class 7: 7- segment LED
Class 8: 1-digit LED
Class 9: DC Motors
- Using transistor
- H-bridge and breadboard power supply
Class 10: Additional devices Overview
- Radio signals
- Bluetooth
- GPS
- Description of Final Project
그 외 세부 사항
수업 자료
Students need to either have an account with www.autocad.com to use the free TinkerCad circuit simulator or download the free Arduino IDE (version 1.8.13) from www.arduino.cc to use with the Arduino components. You can buy the components separately, but it would be more expensive than buying a kit that has all the parts you need and more. Recommended Devices/kits if you are purchasing components separately: Arduino Uno (or clone) with USB cable (or Arduino MEGA) solderless breadboard 3 different color LEDs 1-3 pushbuttons 1 potentiometers 1 rotary encode (optional) 1 servo motor 1 ultrasonic sensor 1 passive piezo buzzer 1 stepper motor and motor driver 1 DC motor 1 breadboard power supply or transistor 1 active buzzer 1 passive buzzer 1 LCD, preferably with I2C module adapter (see below) 1 LED array 1 7-segment LED (1 digit) 1 - 4- digit LED 1 micro servo 1 continuous servo (optional) Many male-male jumper wires of different colors Many male-female jumper wires of different colors Resistors varying from 100-ohm to 1M-ohm Recommended Kit that contains all the parts: https://www.amazon.com/EL-KIT-001-Project-Complete-Starter-Tutorial/dp/B01CZTLHGE/ref=asc_df_B01CZTLHGE/?tag=hyprod-20&linkCode=df0&hvadid=241907595991&hvpos=&hvnetw=g&hvrand=8544331822937541734&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9015321&hvtargid=pla-464156272733&psc=1 This will make the LCD easier to work with: https://www.amazon.com/Qunqi-Serial-Backlight-Arduino-MEGA2560/dp/B01E4YUT3K/ref=pd_rhf_se_p_img_2?_encoding=UTF8&psc=1&refRID=82F2F1N5PA4D76EEHV6H
Outschool 외 필요 앱/웹사이트
이 수업에서는 아웃스쿨 교실 외에도 다음의 툴을 사용합니다:
출처
Students will need to download a free copy of the Arduino IDE located at www.arduino.cc. Students may also want to have an account at www.tinkercad.com so they can try out some code before using the Arduino IDE.
선생님을 만나보세요
교사 전문성 및 자격증
오하이오 교직증명서 중등교육에
2 정도
석사 학위 과학 Case Western Reserve University에서
학사 학위 과학 Stern College for Women Yeshiva University에서
My classes will teach you coding skills needed to program an Arduino microcontroller. In these classes you will learn about the Arduino and how to write code that allows it to read input from sensors and send output to actuators. You will be guided through the wiring and coding for each type of sensor and actuator so that you will eventually be able to create your own inventions.
I have been a private school middle and high school science teacher for over 30 years. During that time, I taught classes in chemistry, engineering, earth science, life science, chemistry, forensic science, biology, and health. I enjoy teaching through hands-on experimentation and I believe that students learn best when they are activity engaged in the learning process.
I am an amateur photographer and love to photograph my grandchildren, my dog, and wildlife. I enjoy creating scrapbooks from my photos. I also enjoy tinkering with my Arduino and 3D printer to create inventions of my own.
리뷰
Elene Feigenbaum님의 다른 수업
Elene Feigenbaum님의 다른 수업
다른 인기 수업
Arduino 코딩 1부: LED, 서보, 버튼, 부저 등
Elene Feigenbaum
4.9
(139)
US$18회당 수업료
다음 세션은 Monday 11 PM 에 예정되어 있습니다.
그룹 수업
10 주, 주당 1회55분
10-15 세
Arduino 코딩 3부: 엔지니어링 프로젝트에서 전자 액추에이터 사용
Elene Feigenbaum
4.9
(139)
US$18회당 수업료
다음 세션은 Wed 3/5 8 PM 에 예정되어 있습니다.
그룹 수업
5 주, 주당 2회55분
13-17 세
1:1 튜터링: 코딩, 아두이노, 게임, 유니티, 파이썬, 자바스크립트, C++, C#
Alex Fish
5.0
(5)
US$60 세션당
일대일 레슨
온디맨드
7-18 세
Tinkercad 로봇 연구실: Arduino와 Microbit으로 가젯을 설계, 코딩, 제작해 보세요!
Create n Learn: English, Coding, AI, Music, Math
4.9
(201)
US$17회당 수업료
다음 세션은 내일 12 AM 입니다.
그룹 수업
5 주, 주당 2회55분
8-10 세
10~14세를 위한 개인화된 라이브 코딩 랩 [3:1 비율]
CodeWithUs
4.2
(137)
US$29회당 수업료
다음 세션은 Friday 7 PM 에 예정되어 있습니다.
그룹 수업
주당 1회1 시간
10-14 세
6~11세를 위한 라이브 코딩 수업
Usama Puri
4.3
(21)
US$30회당 수업료
다음 세션은 오늘 10 PM 입니다.
그룹 수업
주당 1회55분
6-11 세
선생님 톰과 함께하는 STEM 멘토링! 1:1로 STEM 프로젝트를 자신의 속도에 맞춰 탐색하세요
Teacher Tom Bickmore
5.0
(273)
US$75 세션당
일대일 레슨
온디맨드
5-18 세
6~11세를 위한 코딩 및 비디오 게임 디자인
Usama Puri
4.3
(21)
US$30회당 수업료
다음 세션은 Sunday 6 PM 에 예정되어 있습니다.
그룹 수업
주당 1회55분
6-11 세